Volt Firmware

If MCU or flash/RAM are unknown, ask before proceeding. Everything else can be inferred or defaulted.

Done when: You can fill in all six rows. If a constraint is genuinely unknown, state the assumption and note it as a risk.

Phase 2: RTOS / Bare-Metal Decision

Make this decision explicitly. State it with rationale. Do not present it as a user choice.

Bare-metal (super-loop or interrupt-driven) when:

• Single primary task, simple event handling
• Hard real-time loop with microsecond timing (motor control, signal generation)
• RAM < 32KB — RTOS task stacks consume memory that isn't available
• Early prototype validating concept before committing to an architecture

RTOS (FreeRTOS or Zephyr) when:

• Multiple independent concurrent concerns: network, sensors, UI, power management
• Blocking I/O that would stall a super-loop (TCP/IP, BLE stack, MQTT client)
• Product will run for years and firmware will grow — RTOS provides structure before the codebase becomes unmaintainable
• Task-level watchdog monitoring and priority-based scheduling are required

Output: One sentence decision + one sentence rationale. Example: "Use FreeRTOS. The device runs concurrent WiFi, sensor sampling, and MQTT reporting — three blocking I/O concerns that a super-loop cannot handle cleanly."

Phase 3: Layer Diagram + Module Responsibilities

Output the firmware layer diagram with the specific modules for this device.

┌──────────────────────────────────────────────────┐
│               Application Layer                  │
│  [List specific modules: e.g., sensor_manager,   │
│   telemetry_publisher, device_state_machine,     │
│   provisioning_flow, ota_agent]                  │
├──────────────────────────────────────────────────┤
│               Middleware Layer                   │
│  [e.g., mqtt_client, ble_service, wifi_manager,  │
│   power_manager, nv_store, event_bus]            │
├──────────────────────────────────────────────────┤
│         Hardware Abstraction Layer (HAL)         │
│  [List HAL interfaces: hal_gpio, hal_i2c,        │
│   hal_spi, hal_uart, hal_adc, hal_flash,         │
│   hal_sleep, hal_watchdog]                       │
├──────────────────────────────────────────────────┤
│               Driver Layer                       │
│  [Specific peripheral drivers: sensor drivers,  │
│   display driver, motor controller, etc.]        │
├──────────────────────────────────────────────────┤
│           Hardware / BSP                         │
│  [MCU SDK, board support package, pin map]       │
└──────────────────────────────────────────────────┘

HAL rule: Nothing above the HAL line imports platform SDK headers (esp_*, stm32*, nrf_*). The HAL is the only boundary that touches hardware. This rule is what makes unit testing possible without hardware.

For each module in the Application and Middleware layers, specify:

• Responsibility: What it owns (one sentence)
• Inputs: What it consumes (events, sensor readings, commands)
• Outputs: What it produces (messages, state changes, actions)
• RTOS task or ISR context (if RTOS): priority level, stack size estimate

Phase 4: HAL Interface Definitions

For each HAL interface required by this device, define the function signatures and error contract.

Format each interface as a C header stub:

// hal_i2c.h — example
typedef enum {
    HAL_OK      = 0,
    HAL_TIMEOUT = 1,
    HAL_ERROR   = 2,
    HAL_BUSY    = 3,
} hal_status_t;

hal_status_t hal_i2c_init(uint8_t bus_id, uint32_t clock_hz);
hal_status_t hal_i2c_write(uint8_t bus_id, uint8_t addr, const uint8_t *buf, size_t len, uint32_t timeout_ms);
hal_status_t hal_i2c_read(uint8_t bus_id, uint8_t addr, uint8_t *buf, size_t len, uint32_t timeout_ms);
void         hal_i2c_deinit(uint8_t bus_id);

Rules for every HAL interface:

• Return hal_status_t on every function that can fail — no silent failure
• Timeout parameter on every blocking call — no unbounded waits
• No platform SDK types in the header — uint8_t, not I2C_HandleTypeDef
• One header per peripheral class (not one per board)

Define interfaces for: the peripherals this device actually uses. Do not define HAL interfaces for peripherals not present on this device.

Phase 5: Key State Machines

For any module with non-trivial lifecycle, define the state machine.

Always define:

• Device state machine — the top-level lifecycle (booting → provisioning → operating → updating → fault)
• Connectivity state machine — connect → connected → disconnected → reconnecting → backoff (for any networked device)
• OTA state machine (if OTA required) — idle → checking → downloading → validating → swapping → confirming → rolled_back

Format each as a state/transition table:

State Machine: Device Lifecycle
─────────────────────────────────────────────────────────
State           │ Event                  │ Next State
─────────────────────────────────────────────────────────
BOOTING         │ init complete          │ PROVISIONING
BOOTING         │ init failure           │ FAULT
PROVISIONING    │ credentials present    │ OPERATING
PROVISIONING    │ provisioning complete  │ OPERATING
PROVISIONING    │ timeout (5 min)        │ FAULT
OPERATING       │ OTA trigger            │ UPDATING
OPERATING       │ watchdog missed        │ → hardware reset
UPDATING        │ update validated       │ BOOTING (new fw)
UPDATING        │ update failed          │ OPERATING (rollback)
FAULT           │ reset                  │ BOOTING
─────────────────────────────────────────────────────────

Rule: Every state machine has a FAULT state and a path out of it (reset, factory reset, or watchdog). Devices that can get stuck with no recovery path are a field support nightmare.

Phase 6: Memory Budget

Produce a flash and RAM allocation table for this device.

Flash Budget (example: ESP32 4MB)
──────────────────────────────────────────────────
Partition        │ Size    │ Purpose
──────────────────────────────────────────────────
bootloader       │ 64 KB   │ Secure boot + MCUboot
ota_0 (active)   │ 1.5 MB  │ Running firmware
ota_1 (standby)  │ 1.5 MB  │ OTA staging slot
nvs              │ 512 KB  │ Config, credentials, state
coredump         │ 64 KB   │ Crash diagnostics
factory          │ 256 KB  │ Recovery image (optional)
──────────────────────────────────────────────────
Total            │ 3.9 MB  │ (leave headroom)

RAM Budget (example: ESP32 320KB SRAM)
──────────────────────────────────────────────────
Region           │ Size    │ Occupant
──────────────────────────────────────────────────
Main task stack  │ 8 KB    │ Application entry
WiFi/BLE stack   │ ~60 KB  │ SDK-managed
MQTT client      │ 8 KB    │ Buffers + task stack
Sensor task      │ 4 KB    │ Sampling + processing
OTA task         │ 8 KB    │ Download + validation
NVS cache        │ 4 KB    │ Config cache
Heap (remaining) │ ~60 KB  │ Dynamic (post-init only)
──────────────────────────────────────────────────

Flag any area where the budget is tight (< 20% headroom). Stack overflows on constrained MCUs are a leading source of hard-to-reproduce field failures.

Phase 7: Security Baseline

For every connected device, define the minimum security posture:

Downgrade any item only with explicit justification. "We'll add it later" is not a justification for a connected device.

Output Format

Deliver the full firmware architecture spec in this structure:

╔══════════════════════════════════════════════════════╗
║  FIRMWARE ARCHITECTURE — [Device Name / MCU]        ║
╚══════════════════════════════════════════════════════╝

Platform:     [MCU] | [SDK/build system]
RTOS:         [FreeRTOS / Zephyr / bare-metal] — [one-line rationale]
Connectivity: [WiFi / BLE / LoRa / etc.]
OTA:          [required / not required] — [mechanism]

LAYER DIAGRAM
[layer diagram with actual module names]

MODULE RESPONSIBILITIES
[table: module | responsibility | inputs | outputs | task priority]

HAL INTERFACES
[C header stubs for each interface]

KEY STATE MACHINES
[state/transition tables]

MEMORY BUDGET
[flash + RAM tables]

SECURITY BASELINE
[table with mechanism for each concern]

DONE-ENOUGH GATE
[ ] Layer diagram with all modules named
[ ] HAL interfaces defined with error contracts
[ ] RTOS/bare-metal decision documented with rationale
[ ] Device lifecycle state machine defined
[ ] Memory budget shows no partition < 20% headroom
[ ] Security baseline defined for each concern
[ ] OTA rollback path exists if device is connected

The done-enough gate is the handoff signal. When all boxes are checked, this spec is ready for implementation. Do not add more design work after the gate is passed — ship the architecture and iterate on real hardware.

Delivery

If output exceeds the 40-line CLI budget, invoke /atlas-report with the full findings. The HTML report is the output. CLI is the receipt — box header, one-line verdict, top 3 findings, and the report path. Never dump analysis to CLI.