Volt Ota

If flash size or connectivity are unknown, ask before proceeding. Everything else can be defaulted with stated assumptions.

Phase 2: Partition Layout

Design the flash partition layout for safe OTA. The core rule: never overwrite the running firmware.

A/B Dual-Partition (default for MCUs with >= 2MB flash)

Flash Layout — ESP32 4MB example
─────────────────────────────────────────────────────────
Address      │ Size    │ Partition  │ Purpose
─────────────────────────────────────────────────────────
0x0000_0000  │ 64 KB   │ bootloader │ Secure boot + OTA logic
0x0000_8000  │ 4 KB    │ otadata    │ Active slot selector (2 sectors, power-safe)
0x0000_9000  │ 512 KB  │ nvs        │ Config, credentials, version tracking
0x0008_1000  │ 16 KB   │ coredump   │ Crash diagnostics (post-mortem OTA analysis)
0x0008_5000  │ 1.5 MB  │ ota_0      │ Slot A — active firmware
0x001E_5000  │ 1.5 MB  │ ota_1      │ Slot B — OTA staging slot
─────────────────────────────────────────────────────────

otadata partition is two flash sectors written redundantly. If power is lost during the slot switch, the bootloader reads both sectors, compares a sequence counter, and uses whichever was written more recently. This is the power-safety mechanism for the partition swap itself.

Single-Partition with Backup (for MCUs with < 2MB flash)

When flash is too constrained for two full app slots, use MCUboot's "overwrite-only" mode with a scratch partition, or delta/incremental updates. Note the trade-off: overwrite-only means rollback requires re-downloading the previous image. Document this explicitly — it changes your recovery SLA.

MCUboot (Zephyr, nRF) equivalent layout

─────────────────────────────────────────────────────────
Partition    │ Size    │ Purpose
─────────────────────────────────────────────────────────
boot         │ 48 KB   │ MCUboot bootloader
slot0_ns     │ ~700 KB │ Active firmware (primary slot)
slot1_ns     │ ~700 KB │ OTA candidate (secondary slot)
scratch      │ 128 KB  │ Swap scratch area (for swap mode)
storage      │ 32 KB   │ Settings + version state
─────────────────────────────────────────────────────────

Phase 3: Update Flow

Define the complete update flow from trigger to confirmed boot. Every step is explicit.

OTA Update Flow
─────────────────────────────────────────────────────────
1. TRIGGER
   Device polls update server (scheduled interval or push notification)
   Request: GET /firmware/latest?device_id={id}&hw_rev={rev}&current_version={semver}
   Response: { version, size, sha256, signature, download_url, mandatory: bool }
   Decision: skip if current_version >= available version (unless mandatory)

2. PRE-DOWNLOAD CHECKS
   [ ] Battery level >= threshold (skip if < 20% on battery-powered device)
   [ ] Sufficient flash space in inactive slot
   [ ] Network connectivity stable (RSSI above floor for WiFi/BLE)
   [ ] Not in a critical operation (active sensor reading, calibration, etc.)

3. DOWNLOAD
   HTTPS GET with Range header support for resume
   Write in chunks directly to inactive slot (never buffer full image in RAM)
   Track last-written byte offset in NVS — resume from here on reconnect or power loss
   Progress: emit telemetry event every N chunks (visible in fleet dashboard)

4. VALIDATION
   [ ] SHA-256 of complete written image matches manifest sha256
   [ ] ECDSA/RSA signature verification using public key embedded in bootloader
   [ ] Version number in image header > anti-rollback floor
   [ ] Image size matches declared size
   FAIL on any check → mark slot invalid, report failure, retain running firmware

5. SLOT SWAP (atomic)
   Write otadata / MCUboot image trailer to mark inactive slot as PENDING
   Reboot — bootloader sees PENDING flag and boots from new slot
   New firmware boots in UNCONFIRMED state

6. HEALTH CHECK (in new firmware, within confirmation window)
   New firmware must explicitly confirm health: esp_ota_mark_valid_context() / boot_write_img_confirmed()
   Confirmation window: configurable, default 60 seconds
   Health check criteria: WiFi connected, MQTT connected, sensor reading valid, no crash loop

7. CONFIRMATION
   Health check passes → mark slot CONFIRMED → update is complete
   Report success: POST /firmware/status { device_id, new_version, status: "success" }

8. ROLLBACK (if health check fails or confirmation window expires)
   Watchdog fires OR reboot before confirmation → bootloader sees UNCONFIRMED slot → reverts to previous slot
   Previous slot is always preserved — never written during an OTA update
   Report failure: POST /firmware/status { device_id, attempted_version, status: "rolled_back", reason }
─────────────────────────────────────────────────────────

Phase 4: Rollback Conditions + Failure Modes

Define every failure mode explicitly. "It will just rollback" is not a failure mode — this is.

Failure Mode Analysis
─────────────────────────────────────────────────────────────────────
Scenario                    │ Behavior                │ Recovery
─────────────────────────────────────────────────────────────────────
Power loss during download  │ Resume from NVS offset  │ Automatic on reconnect
Power loss during slot swap │ otadata redundancy safe  │ Bootloader resolves on next boot
New firmware crashes on boot│ Watchdog fires → revert │ Automatic rollback to previous slot
Health check timeout        │ Reboot → revert         │ Automatic rollback
Signature verification fail │ Slot marked invalid     │ Retain running firmware, report
SHA-256 mismatch            │ Slot marked invalid     │ Retain running firmware, report
Download corruption         │ SHA-256 catches it      │ Re-download from scratch
Server unreachable          │ Skip update, retry next │ No change to device state
Anti-rollback violation     │ Reject image            │ Retain running firmware, report
Flash write error           │ Mark slot invalid       │ Retain running firmware, report
Crash loop in new firmware  │ Max reboot counter → revert │ Automatic rollback
─────────────────────────────────────────────────────────────────────

Crash loop detection: Track reboot count in NVS. If new firmware reboots N times within M seconds of boot (before confirmation), treat as rollback trigger. Reset counter on confirmed boot.

The one scenario you cannot recover from OTA: Bootloader corruption. Protect the bootloader partition with a write-protect fuse (ESP32 eFuse, STM32 write protection). The bootloader is never updated via OTA.

Phase 5: Validation Checks Detail

Enumerate every validation check, the mechanism, and the fail-closed behavior.

Key signing architecture:

Build server:
  openssl ecparam -name prime256v1 -genkey -noout -out private_key.pem
  openssl ec -in private_key.pem -pubout -out public_key.pem
  [Sign firmware binary during CI/CD — private key NEVER leaves build server]
  [Public key embedded in bootloader at manufacturing time]

Device:
  [Bootloader verifies signature before any new image boots]
  [Application verifies signature before writing to inactive slot]

Phase 6: Fleet Management Approach

Scale the fleet management approach to deployment size.

< 100 devices: Direct push via cloud IoT platform (AWS IoT Jobs, Golioth OTA, Particle). No staged rollout needed. Track status in a spreadsheet or simple dashboard.

100 – 10K devices: Staged rollout essential.

• Canary cohort (1–5%): push to a small group first, monitor for rollbacks and error reports for 24–48 hours
• Green light gate: if rollback rate < 1% and error rate normal, promote to full fleet
• Rollout speed: 10% → 25% → 50% → 100% with gate checks between each stage

> 10K devices: Fleet management platform required (Mender, Golioth, Balena, AWS IoT Jobs with deployment groups). Automated gate checks, per-cohort rollback, update scheduling by timezone/connectivity window.

Update server API contract:

# Version check
GET /firmware/latest?device_id={id}&hw_rev={rev}&current_version={semver}
→ 200 { version, size_bytes, sha256, download_url, mandatory, signature_b64 }
→ 204 No Content (device is up to date)

# Download (supports Range for resume)
GET /firmware/download/{version}
Range: bytes={offset}-
→ 206 Partial Content (binary firmware chunk)

# Status report
POST /firmware/status
{ device_id, hw_rev, previous_version, new_version, status: "success"|"rolled_back"|"failed", reason, timestamp }
→ 200 OK

Phase 7: Implementation Artifacts

List every artifact the implementation requires. Volt produces the spec and scaffolding; implementation fills them in.

ota/
  ota_agent.h          — public API: ota_check(), ota_start(), ota_confirm_health()
  ota_agent.c          — state machine implementation
  ota_validate.c       — SHA-256 + signature verification
  ota_partition.c      — partition layout helpers, slot selection
  ota_fleet.c          — server communication, version check, status reporting

hal/
  hal_flash.h          — HAL interface for flash read/write/erase (used by ota_partition.c)

scripts/
  sign_firmware.sh     — CI/CD signing step (wraps espsecure.py or imgtool.py)
  gen_keys.sh          — One-time key generation (run once, store private key in secrets manager)

config/
  partitions.csv       — Partition table (ESP-IDF) or dts overlay (Zephyr)
  ota_config.h         — Confirmation window, retry limits, canary thresholds

Output Format

Deliver the complete OTA system design in this structure:

╔══════════════════════════════════════════════════════╗
║  OTA UPDATE DESIGN — [Device Name / MCU]            ║
╚══════════════════════════════════════════════════════╝

Platform:      [MCU] | [OTA mechanism: ESP-IDF / MCUboot / Mender]
Connectivity:  [WiFi / BLE / LoRa / cellular]
Fleet size:    [estimated]
Partition scheme: [A/B dual / single + scratch / delta]

PARTITION LAYOUT
[flash map table with addresses and sizes]

UPDATE FLOW
[numbered steps: trigger → download → validate → swap → health check → confirm/rollback]

FAILURE MODES
[table: scenario | behavior | recovery]

VALIDATION CHECKS
[table: check | mechanism | fail behavior]

SIGNING ARCHITECTURE
[key generation, where keys live, signing step in CI/CD]

FLEET MANAGEMENT
[approach scaled to deployment size, server API contract]

IMPLEMENTATION ARTIFACTS
[file list with responsibilities]

DONE-ENOUGH GATE
[ ] Partition layout defined with sizes — both slots fit in available flash
[ ] Update flow covers every step from trigger to confirmed boot
[ ] Every failure mode has an explicit recovery path (no "TBD")
[ ] Rollback is automatic — no human intervention required for recovery
[ ] Firmware signing defined — public key placement + CI/CD signing step
[ ] Server API contract defined (version check, download, status endpoints)
[ ] Bootloader partition is write-protected
[ ] Crash loop detection defined (reboot counter + threshold)

The done-enough gate is the handoff signal. When all boxes are checked, this design is ready for implementation. A device with an unfinished OTA design is a device you will regret shipping.

Delivery

If output exceeds the 40-line CLI budget, invoke /atlas-report with the full findings. The HTML report is the output. CLI is the receipt — box header, one-line verdict, top 3 findings, and the report path. Never dump analysis to CLI.